Rb30 cam timing vs ignition

images rb30 cam timing vs ignition

I stuffed up. But every tooth you move the cam, it will adjust it 5 or 6 degrees. In the end i kept the standard timing. I just looked at the diagram and went with it Mar 18, 7.

  • Advancing the cam timing question Just Commodores
  • CAM TIMING [Archive]
  • Ignition Timing Question, Rb30/25De + Turbo. RB30 conversions SAU Community
  • VL cam timing and specs PerformanceForums

  • Slide timing belt onto the camshaft and crankshaft gears ensuring that the marks on the belt are This guide will help you to adjust your idle speed and ignition timing to factory specifications.

    Accelerate the engine two or three times to approximately 2, - 3, RPM without load. Rb30 timing If you know the ignition timing was set to stock (Or whatever else so long as you know what it was) you could get your cam timing back to where. I put a new timing belt on my RB30 yesterday and after reading lots about I tried advancing the ignition timing and it didn't make any difference. Advancing timing on the cam means to turn the cam or distributor against its.
    Now with the adjustable cam gears, i've fiddled with it a few degree's, advanced it a bit further while out at willowbank one night and dropped 0.

    Welcome to SAU Community, like most online communities you must register to view or post in our community, but don't worry this is a simple free process that requires minimal information for you to signup.

    Video: Rb30 cam timing vs ignition Speed Secrets: Understanding Timing For Your Best Tune

    Thinking about it, if you can make the cam come on under rpm or whenever you stall stops slipping thats where you should advance it. Ive put it back to the middle spec ie.

    Advancing the cam timing question Just Commodores

    So unless someone can tell me why I haven't gotten the results promised, I'm going back to the standard settings. Mar 18, 7. Now that I've done it three times in two days, I've got it down to an easy hour and a half job.

    images rb30 cam timing vs ignition
    CENTRO LUSO VENEZOLANO VARGAS PIN-UP
    Just Commodores.

    The key position and marks line up when you stack them on top of each other.

    Posted February 10, edited. Then, you need to remove the distributor cap and ensure that the rotor button is pointing at cylinder one like this:. Initially I thought maybe the 30 balancer had a different key position to the 25 balancer. I was under the impression that some technical books came out mistakenly quoting that it was 52 teeth between these 2 marks instead of the correct 53, and by putting it as 52 teeth, this made the car run sluggish down low or have a retarded effect on the motor.

    › › VL Non-Turbo Discussion.

    [Archive] CAM TIMING VL Non-Turbo Discussion. Why is it? because the cam was advanced? or because the ignition timing was advanced?

    CAM TIMING [Archive]

    › › RB30 conversions.
    Now with the adjustable cam gears, i've fiddled with it a few degree's, advanced it a bit further while out at willowbank one night and dropped 0. InsaneVLyes, it is a large cam - and doesnt respond well without a chip looking into getting one done if i cant afford a whole new turbo engine soon.

    Isn't that the 1st coil anyway?

    images rb30 cam timing vs ignition

    By rehab Started June 26, Or am i all backwards over this???? Ok, Assuming the cam in an RB30 rotates in a clockwise direction, then turning the cam clockwise relative to the belt will advance it.

    images rb30 cam timing vs ignition

    images rb30 cam timing vs ignition
    Outside magazine online editor
    I suppose I should apply a bit more thought to my own posts My cars running how i like it now, so its time for me to go out and see how slow it is, and figure out how to drive it in a straight line.

    You'll enjoy the driveability more instead of having to flat foot it off the line. What you are doing is actually retarding the cam by turning it forwards in its direction of rotation.

    Click here to register. By advancing the cam, you are making the events happen earlier according the the piston RPM so then you make better low rpm power.

    Ignition Timing Question, Rb30/25De + Turbo. RB30 conversions SAU Community

    Posts Latest Posts.

    Also, have you disconnected the TPS or AAC valve (can't remember which you disconnect on RB25) to put it into base timing mode.

    If its miles.

    Video: Rb30 cam timing vs ignition ECU Chip Tune - Ignition Timing - Increase Horsepower

    › forums › forum › technical › general-aa. I've run into more than a few people who swear by advancing the cam of the RB30 1 is 52 teeth between timing marks instead of
    From the other side of the argument i also understand that to make power come on earlier you want the valves to open earlier than they would which means turning the cam clockwise same as setting it to 52 teeth on the belt but then why does that not make the vl perform better?

    When its at tdc on 1 the 0' lines up with the timing cover. Why is it? Mar 18, 7.

    VL cam timing and specs PerformanceForums

    Slowly getting there.

    images rb30 cam timing vs ignition
    DB 4 FAKE VS REAL LOUBOUTIN
    From the other side of the argument i also understand that to make power come on earlier you want the valves to open earlier than they would which means turning the cam clockwise same as setting it to 52 teeth on the belt but then why does that not make the vl perform better?

    Filtered by:. How are you using the light? What I'm after is more power down low. I suppose I should apply a bit more thought to my own posts I had to re-time my car as it was running fairly badly, really doughy coming off idle.

    0 thoughts on “Rb30 cam timing vs ignition